Die Inventor FAQ wird unterstützt von:

Inventor FAQ Logo

26.02.2014

Vault 2014 Service Pack 2 verfügbar

Hier kann der SP2 für Vault 2014 heruntergeladen werden.

Auszug aus der Readme:

INSTALLATION

  • All clients and servers should be upgraded at the same time to the Autodesk Vault 2014 Service Pack 2
  • All future Autodesk Vault 2014 hotfixes will depend on this Service Pack being installed
  • Depending on how your UAC is configured on Windows Vista or later operating systems, users may need to turn off User Access Control (UAC) to install the Service Pack
  • To install the Service Packs, Administrative privileges are required.
  • The service pack install may take longer than expected in Windows 7 or in Windows Server 2008 R2. To avoid that install the following Microsoft Hotfix:
    http://support.microsoft.com/kb/2663352/en-us
    For other Operating systems ensure Windows Update is up to date.

WARNING: Failure to follow these instructions properly may result in unusable sites. This procedure applies to Single Site, Multi Site and Connected Workgroup deployments.

NOTE: If you intend to install Autodesk Vault 2014 Subscription Release 1 for Autodesk Vault Workgroup 2014 or Autodesk Vault Professional 2014, DO NOT install this update. Instead, proceed directly to the installation of Autodesk Vault 2014 Subscription Release 1 for Autodesk Vault Workgroup 2014 or Autodesk Vault Professional 2014.

NOTE: Always ensure that a successful backup has been performed before applying this Service Pack.

Client Service Pack 2 Installation - applicable to every Autodesk Vault Client 2014

  1. Run "Autodesk Vault 2014 Service Pack 2 (Client).msp" on the Vault Explorer client to install the Service Pack.

Server Service Pack 2 Installation - applied to every Autodesk Data Management Server (ADMS)

  1. NOTE: When installing a non ENU version of Vault Basic server, first run "Autodesk Vault 2014 Pre SP1 (Server).msi".
  2. Open the ADMS Console.
  3. Make sure all databases are fully migrated to the latest version.
    1. Migrate all unmigrated databases and libraries before proceeding.
    2. It may be necessary to detach an unmigrated database if the Service Pack addresses a migration problem.
  4. Close the ADMS Console application.
  5. Restart the web service by typing 'iisreset' at the command prompt.
  6. Run “Autodesk Vault 2014 Service Pack 2 (Server).msp” on the ADMS server to install the Service Pack.
    1. DO NOT OPEN ADMS – DATABASE MIGRATION SHOULD BE POSTPONED UNTIL INSTRUCTED BELOW.
  7. Repeat the preceding steps for every ADMS server.
    1. DO NOT OPEN ADMS – DATABASE MIGRATION SHOULD BE POSTPONED UNTIL INSTRUCTED BELOW.

Database Update - applied ONCE from one Autodesk Data Management Server (ADMS) instance as specified.

WARNING: DO NOT PROCEED until Service Pack 2 has been successfully applied on ALL ADMS servers.

  1. Use the appropriate server and ADMS Console application.
    1. Single Site, use your only ADMS Console.
    2. Multi-Site (file replication), use any of the ADMS consoles.
    3. Connected Workgroup (file and SQL replication) use one of the ADMS Consoles on the Publisher Workgroup.
  2. Restart the web service by typing 'iisreset' at the command prompt.
  3. Open the ADMS Console and perform the database migration.
  4. If necessary, attach any previously detached databases and allow the migration to complete.

NOTE: On Connected Workgroup environments, the SQL snapshot agent may not handle generating the initial snapshot. If this occurs, restart the SQL snapshot agent.

SUMMARY OF ISSUES ADDRESSED

  1. Decimal separators that are not a dot would cause unexpected results for property mapping in non ENU applications.
  2. Date formatting was not being honored in non ENU applications.
  3. Importing a Vault configuration would fail when a referenced content source provider does not exist in the Vault.
  4. Change State restriction exposed the name of file to which a user had no access permission.
  5. When Assigning an item, files checked in from a non ENU client, using a comma decimal symbol, using mapped UDP to File and Item Categories, resulted in an Error 155.
  6. Solved an issue where selecting the Uses tab would result in a Vault Explorer crash for certain assemblies.
  7. When attempting to edit properties on DWF or ZIP files, the fields were greyed out and not editable.
  8. Fixed a performance problem when gathering 'release biased' file associations when 'include related documentation' is specified. This sometimes resulted in Inventor Open From Vault on a previous version to fail.
  9. Require Inventor users to select a numbering scheme or file name in a certain scenarios (example; creating symmetry and mirroring) to prevent an Inventor crash.
  10. Inventor would crash when closing drawing files after adding "Document settings" button to the Quick Access Toolbar.
  11. Using a double byte slash character would cause undesirable results for Vault folder and file names.
  12. Job Processor Updates
    1. Improved the processing of queued jobs if the Job Processor process is suddenly restarted.
    2. Solved an issue with Job Processor Command Line Parameters being ignored.
    3. Solved running Job processor with Windows Authentication credentials.
    4. For environments with more than one Autodesk Vault File Store (AVFS) servers, jobs submitted to the Job Processor Queue on AVFS1 would be processed on AVFS2.
  13. Enabled logging of all file downloads from Vault.
    1. NOTE: It is necessary to add the following line in Web.Config to the <switches> section to enable this feature;
    2. <add name="LogFileDownloadsBooleanSwitch" value="1"/>
  14. Logging in from Vault 2014 Client and 2013 Client at the same time and with the same username would consume 2 licenses.
  15. Using the command line parameter -S for Connectivity.WorkspaceSync.exe would result in an error "Not a valid settings file path".
  16. A performance improvement displaying the check out dialog when there are many User Defined Properties.
  17. Attempting to map properties for Civil 3D based DWGs would result in the message "The selected file did not contain any mappable properties."
  18. Files would not open from Vault if a user chose not to overwrite a local (newer) one.

Keine Kommentare:

Kommentar veröffentlichen

War der Beitrag hilfreich oder hast du eine Ergänzung dazu?
Ist noch eine Frage offen?
Ich freue mich auf deine Rückmeldung!

Hinweis: Nur ein Mitglied dieses Blogs kann Kommentare posten.

Related Posts Plugin for WordPress, Blogger...
Inventor FAQ Newsletter. Emailadresse: